ELTRON LP2642 DRIVER DOWNLOAD

Place this switch in the OFF 0 position to remove power when you have finished using your printer. Turn the thumb screw holding Rewinding Step 2 the bracket to the printer chassis counter clock- wise to loosen. This is referred to as a Form Feed. Ensure that Print Configuration Control switch setting match the print mode. Page 23 Operation Label Loading Open the top and right side cover on the printer. Operation Cleaning The As you use your printer, the print head may be- Print Head come dirty resulting in poor print quality. When power is first ap- plied with labels loaded, tapping the FEED Control will cause the paper to advance to the top of the next label.

Uploader: Jugrel
Date Added: 16 March 2011
File Size: 36.23 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 3511
Price: Free* [*Free Regsitration Required]

Print Quality, The print darkness or density can ll2642 changed by using the Print Quality option. Eltron lp2642, contact the dealer where you purchased your printer. Page 24 Operation Label Loading Open the Printhead Assembly by pushing the release lever to the right, towards the back of Step the printer.

Installation This section provides information on the installation of the printer and software. eltron lp2642

Eltron TLP2046 User Manual

Swing the bracket eltron lp2642. Table Of Contents Introduction The battery may explode causing damage or injury. Operation Label Loading Open the Printhead Assembly by pushing the release lever eltron lp2642 the right, towards the back of Step the printer.

Insufficient memory for label size. Follow the installation instructions on eltron lp2642 screen to install the software. Figure Eltron lp2642 Ribbon Tape Getting Started Step 4 The printer has a ektron configuration switch bank located on eltron lp2642 back panel of the printer. For the name of a dealer in your area, eltrron 1 Operation Transfer Ribbon Open the printhead assembly. Operation Battery Replace the battery by lifting the battery retain- ing clip up and inserting the new battery in with Replacement Step 4 the printed side up.

Operation This section provides information on the op- eration of the Eltron lp2642 printer. Got it, continue to print. Also See for LP Eltron lp2642 manual – pages. Operation Label Variations Your TLP is equipped with a sensor ca- pable of detecting the gap between labels while and the they are being printed. Use only Eltron approved labels and eltron lp2642. Perform AutoSense gap sensor adjust- ment. Print Speed Selecting a slower print speed can improve the appearance of lines and text on lo2642 label stocks.

Step Perform steps of the Loading Labels proce- dure. Comments to this Manuals Your Name.

Try This  SLEH 00030 EYETOY DRIVERS FOR MAC DOWNLOAD

Operation Label Loading Open the top and right side cover on the printer. Don’t have an account? Getting Eltron lp2642 Open the top and right side cover by lifting the lip on the lower right side of the cover.

Slide the Replacement Step 3 casing top cover off. Getting Started Step Parallel Interface Eltron lp2642 a suitable parallel printer cable from the Attach Interface computer to the Centronics interface connector Cable at the back of the printer.

Operation Loading Labels Your TLP letron print on continuous eltron lp2642 eltronn paper, direct thermal adhesive backed or Tags labels or non-adhesive tags. Page 28 Operation Step Install the ribbon on the rear eltron lp2642 spindle so that the ribbon feeds from the top of the roll into the ribbon feed slot. Operation Step Close the print carriage and press down firmly at both arrows to lock.

Enter text from picture: Alternate memory cartridges are available that can include a real-time clock standard configu- ration without real-time clockKB of mem- ory and eltron lp2642 Dimensional bar codes.

dltron

ELTRON LP USER MANUAL Pdf Download.

Step Place the printer eltron lp2642 a suitable location that Attach Power allows easy access to all sides of the printer. Top Of Form Sensing Operation Top Of Form To etron different size media, your Sensing printer is equipped with a sensor capable of de- tecting the top of each label or tag. Fold it over the end of the leader and eltron lp2642 in place. Load labels into the printer do not use the Adjustment dispenserthen press and hold the FEED Control while placing the power switch in the ON 1 position.

Save this screw for mounting and storing the bracket. Page 15 Getting Started Figure Removal and Insertion of the Memory Cartridge Insert the memory cartridge into the cartridge slot, eltron lp2642 side towards the center etron the printer.

Print Head Kp2642 new labels are eltron lp2642 into the printer, the print head should be cleaned with a Cleaning Pen.

Operation Step Turn the green wheel to adjust the Label Guides eltron lp2642 match the width of the ektron. Operation Label Loading Close the printhead by pressing down on eltron lp2642 Step 7 sides of the front of the printhead assembly.